M/C cable is not a approved method for electrical wiring for a walk in cooler or freezer. You should refer to articial 300.7 of the national electrical code book for more information.

Subscribe to Channel:

This video by Electrical Industry Network was liked: 207 times

If you like this video by Electrical Industry Network, please support their CHANNEL by clicking on the SOURCE link below and Subscribe.

SOURCE

————————————–

Featuring Your Videos:

By featuring your videos on our blog, your videos will receive hundreds of views daily from our website visitors, you get a backlink to your channel for followers to subscribe to your channel. This is a win/win for SEO for both of us. If you would like your videos or channel highlighted and premiered on our blog for FREE, please contact us.

However, if you no longer want us to premier your channel, and want us to remove your video and not feature your channel anymore, please contact us.

Video Post Disclaimer:

The information contained in the multimedia content (“Video Content”) or post content in general, represents the views and opinions of the original creators of such Video Content or post, and does not necessarily represent the views or opinions of KASRefrigeration.com. The mere appearance of Video Content or the post on the Site does not constitute an endorsement by KASRefrigeration.com or its affiliates of such Video or Post Content. 

The Video Content or Post has been made available for informational and educational purposes only. KASRefrigeration.com does not make any representation or warranties with respect to the accuracy, applicability, fitness, or completeness of the Video or Post Content. KASRefrigeration.com does not warrant the performance, effectiveness or applicability of any sites listed or linked to in any Video Content or Post.

Affiliate Disclosure:

This post and description may also contain some affiliate links, which means that the post creator may receive a small commission at no extra cost to you if you click on some of the product links and decide to make a purchase. This channel is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com

Copyright Issue:

If you find any of your copyrighted material in this post or video, please contact us, so we can resolve the issue.

All rights reserved by respective owners.

24 thoughts on “Electrical Wiring for a Walk in Freezer

  1. patwregan says:

    people do not realize how dangerous hacked electrical work is- save money on the install by not hiring an electrician and run the risk of burning your place down- i just dont get it!!!

  2. Matthew L says:

    MC will not pass inspection for a walk in up in my neck of the wood. Because it's susceptible to damage (ie. kitchen staff shoving speed racks and stuffing boxes of pre-made food).

    It's unfortunate but the state I live in allows tradesmen to be licensed for electrical wiring in their respected field, so often times I see work like this too….. Nice video though.

  3. pttanz says:

    Well the way I would've done it would to come out of the Jbox. The conduit would stop about a foot above the box with a cross over connector and into the Jbox with greenfield with an MC connector. I know your not connecting to a direct motor, but we have motors in the machine. But everyone does it differently. Except for that mess. Lol

  4. 2020 Subaru WRX 6spd Manual says:

    Figure out how many wires you need, 4 for a cooler and 6 for a freezer(you need two extra wires for the defrost heaters and defrost termination switch. Which I don't think is necessary if you set the timer correctly.) and use seal-tight, the gray colored "hose" and fittings to make a proper "whip" for the system. Conduit is great too, but I prefer seal-tight.

  5. Sovek says:

    I just got done putting one of these up last night. We used a bell box on the ceiling with a 1/2" EMT "nipple" through the roof, into a j-box, and from the bell box ran SO cord with receptacle, 208 single phase. The old ones were wired the same way.

    Previous store we used seal tite from a bell box into the freezer

  6. Kevin Sullivan says:

    Guess who is ripping off Ductless Heat Pump Jobs from HVAC contractors??? Electricians. Lots of distrust in the trades. Governments not enforcing rules, yet complaining of shortage of tradesmen. Electricians also lose many jobs to other trades or DYI guys, or handymen. Once the ball gets rolling with the govt having a blind eye, then pretty soon the licensed and insured companies that should be doing those particular jobs have a hard time or cant survive at all.

  7. spelunkerd says:

    I'm surprised they would do the connection inside the cooler itself. When ambient temp falls inside the cooler, atmospheric water condenses and corrosion is accelerated, even inside a closed box. Better to make the connection inside an accessible room temperature box outside the cooler. Perhaps there was no option?

Leave a Reply

Your email address will not be published. Required fields are marked *